I found another post that tells what to set the environment to:
Set the board type to “Arduino Pro or Pro Mini” and the processor type to “ATMega328p 3.3v 8mhz”
NOTE: Kevin the Docs (PDF) should be changed to add this. it currently says the board is UNO.
I have used the Arduino Programmer before (Neopixel googles from Adafruit).
I installed the FTDI driver and it shows up as COM3 when I plug the Rover in.
I loaded the PiControl BaseSketch and am able to compile it. Whne I go to upload I get the error below.
Should I choose a different board? the docs says the Rover is a Uno.
When I look at the Board Info I get:
BN: Unknown board
VID: 0403
PID: 6015
SN: Upload any sketch to obtain it
Arduino: 1.8.5 (Windows Store 1.8.10.0) (Windows 10), Board: "Arduino/Genuino Uno"
Sketch uses 6826 bytes (21%) of program storage space. Maximum is 32256 bytes.
Global variables use 642 bytes (31%) of dynamic memory, leaving 1406 bytes for local variables. Maximum is 2048 bytes.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xaa
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xaa
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xaa
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xaa
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xaa
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xaa
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xaa
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xaa
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xaa
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xaa
Problem uploading to board. See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
Trouble Programming Arduino
-
- Posts: 23
- Joined: Sun Jan 14, 2018 1:59 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
-
- Posts: 21
- Joined: Sun Oct 22, 2017 5:30 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Trouble Programming Arduino
it's a bootloader problem sometimes occurring on non-genuine avrdude processors ;-( You'll find a lot of posts on it at this formum. I was lucky to find a way out, decribed here: viewtopic.php?f=18&t=8031&start=10#p9800
-
- Posts: 23
- Joined: Sun Jan 14, 2018 1:59 pm [phpBB Debug] PHP Warning: in file [ROOT]/vendor/twig/twig/lib/Twig/Extension/Core.php on line 1266: count(): Parameter must be an array or an object that implements Countable
Re: Trouble Programming Arduino
Kevin has posted the PDF getting started guide. Does anyone know what the original source for this doc is?
I would be happy to edit it and update it with info like this.. and then check it in to one of the three repos i have created for the code :
viewtopic.php?f=18&t=8054
Marc
I would be happy to edit it and update it with info like this.. and then check it in to one of the three repos i have created for the code :
viewtopic.php?f=18&t=8054
Marc
Who is online
Users browsing this forum: No registered users and 11 guests